Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for University City Homeowners
Water is the quiet killer of masonry chimneys, and in University City it usually gets in at the top. A cracked crown lets rain soak into the brick and mortar below. A missing or loose cap lets water pour straight down the flue while birds, squirrels, and leaves find their way inside. Our technicians have up to 8 years of experience reading exactly that kind of damage, and we fix it with materials built to hold up through Carolina heat, humidity, and the occasional hard freeze. We answer 24/7 at (855) 658-5324, and fast dispatch runs from 7am to 7pm, Sunday through Friday, so we can often get eyes on a failing cap or crown the same day you call.
What Our Chimney Cap & Crown Service Includes
Cap and crown work is preventive engineering. The idea is to stop water and animals at the top of the system before they ever reach the firebox, damper, or liner. Every one of these jobs starts with a close look at what’s actually failing, and we show you what we see before we quote a repair.
Cap Installation
A chimney cap is the lid that sits over the flue opening, and it’s the cheapest protection a chimney can get. You need one if your flue is open to the sky, which is common on older homes around University City where the original cap rusted away or was never fitted. We install stainless and powder-coated caps sized to your exact flue, with a mesh screen that keeps out birds, squirrels, and the leaves that pile up in this part of Mecklenburg County every fall.

Cap Replacement
Caps don’t last forever. Galvanized models rust through, mesh screens tear, and wind gusts work loose the fasteners holding a cap in place. You need a replacement when yours is rusted, rattling, or sitting crooked on the flue. We pull the old cap, check the flue tile underneath for damage the failing cap may have let in, and fit a new one from Olympia Chimney or another professional-grade line so the next one lasts.

Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney that sheds water away from the brick below. When it cracks, water runs into the masonry, freezes in winter, and slowly pushes the chimney apart. You need crown repair when you can see cracks wider than a hairline, crumbling edges, or a crown that has pulled away from the flue. We rebuild failed crowns with a proper slope and overhang so water leaves the chimney instead of soaking into it.

Crown Coating
Crown coating is a flexible, waterproof membrane applied over a crown that’s still structurally sound but showing surface cracks. It’s the right call when the crown hasn’t failed yet but is heading that way, and it extends the life of the original slab at a fraction of a rebuild. We prep the surface, fill the small cracks, and apply a coating that moves with the masonry through freeze-thaw cycles instead of cracking apart.
Multi-Flue Cap
Many University City homes have two or three flues side by side, serving a fireplace, a furnace, and a water heater. Each one needs its own protection, and a single flue cap leaves the others open. You need a multi-flue cap when your chimney has more than one opening under one crown. We build a single stainless unit sized to span all the flues at once, which looks cleaner than a patchwork of individual caps and protects every opening in one install.
Custom Cap
Some chimneys don’t fit a stock cap. Oversized flues, unusual shapes, and chimney stacks with odd dimensions all need something built to measure. You need a custom cap when a standard size won’t seat properly, and forcing one on leaves gaps that defeat the purpose. We take the measurements on site and have a custom stainless cap fabricated to fit, so it sits square and seals the way it should.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with a curated roster of professional-grade chimney brands because the material quality at the top of your chimney determines how long the repair lasts. Olympia Chimney builds stainless caps and multi-flue units we install regularly, and we know which of their configurations suit the flue layouts common on University City homes with more than one appliance venting through one stack. Famco caps are another line we work with, and we’ve learned where their mesh and fasteners hold up best against the wind and summer storms this area gets. When a repair calls for a coated crown system, we look to products like those from Copperfield, and for liner work tied to a cap job we use DuraFlex flexible stainless where the flue needs relining at the same time.
Knowing a brand means knowing how it fails. A cap that’s rusted at the seams, a screen that’s pulled loose at the frame, a crown coating that’s blistered after a few seasons – each points to a different fix, and the brand tells us what to expect when we get up there. Whether you have Olympia Chimney, Famco, Copperfield, or any other make, we can help, and we’ll tell you plainly if a repair makes more sense than a replacement.
Signs You Need Chimney Cap & Crown Right Now
- Water staining on the chimney breast or ceiling. Brown streaks on the masonry inside the house or a damp patch on the ceiling near the chimney usually mean water is getting past the crown or around a failed cap flashing. Left alone, that moisture works into framing and insulation.
- Visible cracks in the crown. Hairline cracks are worth watching. Cracks you can fit a putty knife into, or a crown that’s crumbling at the edge, need repair before the next freeze. Water in a cracked crown expands when it freezes and widens the damage each winter.
- A missing, loose, or rusted cap. If your cap is gone or rattling in the wind, the flue is open to rain, birds, and squirrels. Animals nesting in a flue block the draft and create a fire hazard, and rainwater running down an unprotected flue rusts dampers and damages liner joints.
- Birds, squirrels, or debris in the firebox. Finding nesting material, leaves, or animal droppings in the firebox means something got past the top of the chimney. A proper cap with an intact screen solves it and keeps it from happening again.
- Rust or water marks on the damper. A damper that’s rusted shut or streaked with water stains is telling you moisture is coming down the flue. That’s a cap or crown problem showing up at the bottom of the system, and it’s the reason we always check the top first.
Our Chimney Cap & Crown Process – Step by Step
- 1
We start with a look at the whole system. Before we touch the top, we check the firebox, damper, and flue from below, because water damage at the crown often shows up first at the bottom. Our chimney sweep university city service and inspection work feed into this, and it means we’re not guessing at what needs fixing.
- 2
We get up top and document what we find. On the roof, we inspect the crown, flue tiles, cap, and flashing, and we photograph the damage. You see the same pictures we do, so the recommendation isn’t something you have to take on faith.
- 3
We explain the options and the materials. If the crown can be coated, we say so. If it needs a rebuild, we explain why, and we name the product going on it – a HeatShield or Copperfield crown system, an Olympia Chimney cap, or a custom stainless unit. You get a written estimate before any work starts, and the final price is the one on that estimate.
- 4
We do the repair. Crowns get rebuilt with the right slope and overhang so water sheds off the edge. Caps get fitted square and sealed at the flue, with the screen secured so it doesn’t pull loose. If the flue underneath needs relining, we handle that in the same visit with a DuraFlex liner rather than sending you to another contractor.
- 5
We walk the finished job with you. We show you the completed work, explain what to watch for over the next few seasons, and answer questions. From the firebox floor to the chimney crown, we service the entire system, so there’s no follow-up call to a different trade.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in University City?
A standard single-flue cap installation in University City typically runs $250 to $500, depending on flue size and whether you choose a basic powder-coated cap or a stainless multi-flue unit. Crown repair is usually the larger job: rebuilding a failed crown generally falls in the $500 to $1,200 range, while a crown coating on a sound slab that just needs sealing runs roughly $350 to $700. Custom-fabricated caps for oversized or irregular flues tend to land between $600 and $1,000, since they’re built to measure rather than pulled off a shelf.
Several things move the number. Roof pitch and height affect how long the job takes and how we set up safely. Multiple flues mean more material. And if the flue tile under a failed cap has cracked, the repair may include relining, which is a separate line on the estimate. The way to avoid overpaying is to get the diagnosis in writing with photos, so you can see whether you’re being sold a rebuild when a coating would do.
Every estimate is free, and it’s per job rather than per hour, with the price set by the written estimate before we start. Nothing gets recommended without camera evidence you can see yourself. And if the crown can safely wait a season, we’ll tell you that too.
Chimney Cap & Crown Near University City – Our Service Area
We handle chimney cap & crown work across University City and the surrounding communities, including Harrisburg, Huntersville, Derita, Highland Creek, Hickory Grove, NoDa, Plaza Midwood, Concord, Elizabeth, Myers Park, and Eastover. Travel time depends on where you are relative to the I-85 and I-485 corridors, but most of these areas are within a short drive of our dispatch window. Call and we’ll give you a straight answer on when we can get to your roof. For homeowners closer to the northern edge of the metro, our chimney cap & crown page covers that side of the service area, and there’s more on the Harrisburg area through our chimney cap & crown page as well.
Serving University City, NC – Our Local Coverage Area
We serve University City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in University City
A chimney cap is the lid and screen that sits over the flue opening, and the crown is the concrete slab at the top of the chimney that sheds water away from the masonry. Together they’re the first line of defense against rain, animals, and debris entering the system. When either one fails, water gets into the brick and flue, and that’s where most expensive chimney damage starts. Call (855) 658-5324 for an exact quote – estimates are free.
Most cap installations take under two hours, and a crown coating is usually done in a single visit. A full crown rebuild can take longer, sometimes into a second visit, because the new slab needs to cure properly before it’s finished. We’ll tell you the expected timeline in the written estimate so you can plan around it. We answer 24/7 if you want to talk it through before booking.
Typical ranges in University City run about $250 to $500 for a cap installation, $350 to $700 for a crown coating, and $500 to $1,200 for a crown rebuild, with custom caps often between $600 and $1,000. The exact number depends on flue count, roof access, and whether the repair includes relining. Your written estimate sets the final price, and the estimate itself is free. Call (855) 658-5324 for an exact quote.
Yes. We service Olympia Chimney, Famco, Copperfield, and other professional-grade cap and crown products, and we know where each brand tends to wear out. If your cap was installed by another company, we can inspect it, tell you whether it’s still doing its job, and replace it with the same line or a different one if a better fit makes sense. Call and describe what’s on your roof, and we’ll tell you what to expect.
Same-day work is often possible when you call early, depending on the schedule and the size of the job. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (855) 658-5324 and we’ll tell you what’s available.
We stand behind the workmanship on every cap and crown job, and we’ll go over the specifics with you before the work begins. Manufacturers’ warranties on caps and crown systems vary by product, and we’ll explain what each brand covers so you know what you’re getting. If something isn’t right after the job, call us and we’ll come back out and look at it. Call (855) 658-5324 with questions about a specific product.
Clear access to the fireplace and the area around it, and make sure we can get to the roof safely – move vehicles out of the driveway if ladder access runs that way. Secure pets indoors, and let us know about any roof damage, skylights, or fragile shingles near the chimney so we can plan the setup. If you have questions before we arrive, call (855) 658-5324. We answer 24/7.
Schedule Your Chimney Cap & Crown Service in University City Today
Don’t wait for the next hard rain to find out your crown has failed. We’ll get up there, show you photos of what we find, and give you a written estimate with the materials named before any work starts. Cap and crown work protects the investment you’ve already made in your fireplace, and it’s the repair that prevents the bigger ones. Call (855) 658-5324 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. For the rest of the system, see our chimney repair and inspection services.
Written by the team at Chimney Sweep University City.